Furniture Booth technical parameters spray booth inner diameter: 20000 × 5000 × 5000mm (L × W × H) spray booth outer diameter: 20144 × 6896 × 5600mm (L × W × H) trench: the pit dug two rows, single row Pit dimensions: 18000 × 840 mm (L × W)). Front door: single door, four door, 4000 × 4500mm (W × H), color: optional Operating door: 2, 700 × 2000mm (W × H), color: Optional wall: the wall in the middle with 4 Group steel ribs, top the group with four steel composite beam wall: use thick 70mm, inside and outside δ = 0.5mm color steel, socket type, width 1150 mm, infill material: EPS, color: optional. Lighting: discharge lamp 26 groups × 4 支 = 104 36W lamps, with the next row of lights 18 groups × 4 支 = 72 vertical waist 36W lamp (left / 8, right / 8, after the / 2). Cabinet devices: side motivated wind, after the exhaust, square tube steel frame white mask. Galvanized steel mask. Send exhaust fan base: air with six double inlet centrifugal fans, single wind turbine models and technical parameters are as follows: Model YDW5.6M, power: 7.5KW, flow: 20000m3 / h. Exhaust with three sets of double inlet centrifugal fans, single wind turbine models and technical parameters are as follows: Model: TAE-710H, power: 11KW, flow: 36000m3 / h fan, belt drive. Heating system: with three RG5S Li Ya road fuel burner, 3 stainless steel high efficiency heat exchanger, electric damper actuators 3 spray paint cycle. Maximum heat: 780000Kcal / h filtration system: primary filter, advanced filter, glass cotton filter, M-type activated carbon filter and single-level glass filter pump. Roof: metal folding roof single electronic control system: painting, heating paint, paint, drying time setting, lighting switch, failure indicator, temperature controller power switch, emergency stop switch, when tired. With temperature limiter. Illumination: ≥450LUX maximum operating temperature: 80 ℃ load Winds: ≥0.25m / s Total power: 85KW rapid technological development, paint room equipment is no exception, then the face of the market a wide variety of paint room brand, how to choose Choose a suitable paint room it? So, how kind of paint room it is qualified in general, the quality of the paint room to measure the following aspects: 1. Brightness general, paint the room brightness should reach 800 ~ loo0 lux, and requires the use of light sources close to the D65, while room wall should be matte white; 2. Paint the room air flow uniform flow of air from top to bottom, a flow rate of 0.2 ~ 0.3m / s; 3. It depends on the filtering effect of model paint roof cotton, has a general repair shop to use the EU5 and EU6 two models, when used in paint room in the upper room with sun light exposure is usually very fine dust per square meter should be less than 5 stars; 4. Wall sealing effect. Booths must be sealed at the seams and there should be no accumulation of paint dust; 5. Ensure positive pressure paint room air intake should be slightly larger than the amount of air flow, so that the paint room kept at a positive pressure; 6. Heating system sealing effect around the burner and chimney should be sealed, putty combustion can not occur; 7. Booth from a heating rate of 2O ℃ rose 6O ℃ elapsed time is about lO ~ l5min, should also be aware that some paint room thermometers are not allowed to paint the temperature of the room to prevail when the product surface temperature measurement. After full consideration of the above points, we can not only buy the paint room to the greatest extent possible to meet the requirements for a high level of painting, so that we can spray paint the perfect product in the shortest possible time, but also to master painting bring safe, healthy, bright, comfortable working environment. Address: Zouping Economic Development Zone Tel: 18254381707 QQ: 983843882